 C6 Painted Door Handle & Rear Spoiler Install
With the introduction of the new C6 Corvette, GM created the finest automobiles available, however it seems they left the door open for a few personalized improvements. So what better way to improve the looks of your Corvette than with GM’s own line of bolt-on accessories? To date GM has released door handles, rear license plate frames and rear spoilers painted to match the exterior color of your Corvette. Follow along and we’ll show you just how easy it can be for you to transform your Corvette with a few personalized touches, all available from Zip Products, Inc., 8067 Fast Lane, Mechanicsville, VA 23111, 1-800-692-9632.
Above: All C6 Corvettes come with flat black door handles regardless of the exterior color
|
 |
01: Remove the two Phillips screws on the backside of the handle. |
 |
02: Once the screws are removed, carefully pull back on the bezel just enough to remove it from the door. |
 |
03: |
 |
04: Now carefully push the door opening switch out of the bezel. |
 |
05: This is the door opening switch assembly. |
 |
06: With the new bezel in hand you need to push the switch into the new bezel. This will be a little harder then the original bezel since it is painted. Just apply a little pressure to the switch and it will lock into the bezel. |
 |
07: Install the bezel on the door by placing the lip of the bezel on the outside of the door first. Using light pressure push the bezel until it fully seats in the door. |
 |
08: Re-install the two Phillips screws that you removed from the original bezels. |
 |
09: This is the door bezel installed. |
 |
10: Final shots of the painted door bezels. |
 11: Final shots of the painted door bezels.
Up next, the new rear spoiler...
|
 |
12: This is the stock flat black spoiler that comes stock on all 2005 Corvettes. |
 |
13: The first step in replacing the spoiler is to gain access to the retaining bolts through the taillight openings. You will need to remove the two inboard taillights for this. They are held in place with one T-15 torx screw. |
 |
14: Once the screw is out the taillight can be slipped out of its opening. You can either leave it hanging by the wiring harness or you can disconnect it. |
 |
15: With the taillights out you will need to first reach your hand into the opening in order to get to the brake light that is in the spoiler. You will need to disconnect the harness.
|
 |
16: Using a 10mm socket you will need to remove the 4 retaining nuts that hold the spoiler in place. Once you have removed them, carefully push on the studs pull up on the spoiler until it comes off of the bumper.
|
 |
17: This is the brake light connector that is to be unplugged in step 4.
|
 |
18: Using a 4.5mm 12 point socket you will need to remove the four studs in the spoiler. Two of these are used to retain the brake light, which will also have to be removed. You will install the brake light and the four studs into the new spoiler.
|
 |
19: You will now reinstall the spoiler and the brake lights in the opposite order of which you removed them. Do not over tighten the retaining nuts for the spoiler you could easily crack it. Also do not forget to plug in the brake light or else you are going to be removing the taillights again. As you can see the difference the painted spoiler makes leaves you wondering why it was not done that way to begin with.
|
|
TRANSFORM YOUR C6 CORVETTE:
C6 CORVETTE EXTERIOR ACCESSORIES (PAINTED DOOR HANDLE AND SPOLIER) INSTALLATION
SOURCE:
Zip Products, Inc.
8067 Fast Lane
Mechanicsville, VA 23111
(800) 962-9632
PARTS LIST:
|
Tech. Articles
Comments
Al Reply | Reply with quote | Quote
RSS feed for comments to this post.